Buecher Wuermer

2SCM Transistor Datasheet pdf, 2SCM Equivalent. Parameters and Characteristics. 2SC datasheet, 2SC circuit, 2SC data sheet: NEC – NPN SILICON TRANSISTOR,alldatasheet, datasheet, Datasheet search site for Electronic. 2SC datasheet, 2SC circuit, 2SC data sheet: TEL – Plastic- Encapsulated Transistors,alldatasheet, datasheet, Datasheet search site for.

Author: Karisar Dourg
Country: Morocco
Language: English (Spanish)
Genre: Marketing
Published (Last): 22 July 2014
Pages: 344
PDF File Size: 14.63 Mb
ePub File Size: 14.12 Mb
ISBN: 535-3-84949-594-1
Downloads: 45865
Price: Free* [*Free Regsitration Required]
Uploader: Yozshukasa

It depends on your batch. Vce would be much higher than 1. What could cause transistor to overheat?

Now look in the datasheets to compare those two transistors what is the Vce for such current. It is off the chart, it is a bad sign for this situation. I Googled about, and tried to replace it with a BC Thanks for that, but just want to clarify where do I put the resistor? By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

2SC NEC Npn Silicon Transistor ChipFind Datasheet Archive |

I do not say your circuit is drawing mA, peaks could be higher or lower. Is it possible that there is another problem which caused your transistor to fail and which makes your new transistor hot? Hi, Attila, thanks so much for prompt reply.

  D&D EXPEDITION TO UNDERMOUNTAIN PDF

This is from 2SC datasheet: So power dissipation would be mW, which is above maximum allowed power dissipation. When I replace it with a BC, the circuit doesn’t work at all. I have a circuit in which the C aka 2SC transistor failed after many years. I have short-term access to another C – 2sc200 that in the circuit works just fine, so I know the transistor is the issue. So, transistor could overheat by high Vce or Ic. Sign up or log in Sign up using Google.

I have seen them referred to as ‘switching’ transistors somewhere, I don’t know what that specially means. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Hence a load at its emitter or collector can cause it to have a negative impedance at its base. If not, you have to take out a good oscilloscope and look at the waveforms.

This is being used in a flyback circuit, which switches at approx satasheet kHz or so. It would take too much space to explain the exact mechanism here, but the gist is, the transistor acts as an impedance conversion element at high frequencies due to beta being frequency dependent. Sign up using Facebook.

Hi there Chupacabras, when I replace it with a good C the whole circuit works just fine. My previous, sort-of related question is here: Post as a guest Name. Sign up 2sf2001 Email and Password. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that datasyeet continued use of the website is subject to these policies.

  ASTA METHOD 21.3 PDF

There are huge differences: Well, it’s whether excessive base current, or excessive product of Ic x Vce. Seeing that your circuit has no feedback resistor anywhere on the 2SC, I would suggest to try adding a 10R resistor in the base of dataseet 2SC resp BC after the 22R resistor that goes to the feedback path and see whether that improves the situation.

Transistor General Purpose TO-92

Adding schematic to show what I mean: This would severely limit the lifetime of an already stressed component. So, is there something ‘special’ about the C trannies?

The switching transistor shouldn’t go into breakdown. But it will be lower, say it is mA.

2SC2001 Datasheet PDF

Chupacabras 3, 2 11 Base current is not a problem, it is limited by R to 4. Home Questions Tags Users Unanswered.

Suitable replacement datwsheet 2SC transistor? Thanks, any help appreciated! The additional resistor dampens this oscillation. The BC got kind of warm, and didn’t work.

Another relevant difference could be in hFE.