Buecher Wuermer

View and Download ABB ACS user manual online. ACS Inverter pdf manual download. MTAC pulse encoder interface module user’s manual 3AFE MUL1- R1 installation instructions for ACS, ACS,. ACS, ACS and. ACS Drives Users Manual ACS Three Phase Input. ABB ACS general machinery drives are designed for the OEM machine building sector.

Author: Zolor Malashicage
Country: Malawi
Language: English (Spanish)
Genre: History
Published (Last): 23 June 2014
Pages: 355
PDF File Size: 8.49 Mb
ePub File Size: 6.11 Mb
ISBN: 742-4-88058-310-4
Downloads: 5322
Price: Free* [*Free Regsitration Required]
Uploader: Tolmaran

Table Of Acs530 Diagnostics Symbols Symbols Input continuous rms input current for dimensioning cables and fuses Output continuous rms current. Ul Marking UL marking See the type designation label for the valid markings of your drive. Local control The control commands are given from the control panel keypad when the drive is in local control. COMM Fieldbus interface as the source for the fault reset signal, i. The user macro allows the user to save the parameter settings, including group 99 START-UP DATA, and the results of the motor identification into the permanent memory and recall the data at a later time.

Press key to switch In remote control, the panel display shows text REM. Speed Control Performance Figures Speed control performance figures The table below shows typical performance figures for speed control. Control can also be switched to speed control using a digital input. The brake is re-opened when the requirements set by parameters The programming can be done with control panel or with a PC tool.

Example Air conditioning is active on weekdays from 8: Page Actual signals and parameters The control word is sent by the fieldbus controller via the fieldbus adapter or embedded fieldbus modbus to the drive. User Macros User macros In addition to the standard application macros, it is possible to create three user macros.


Motor Potentiometer Macro Motor Potentiometer macro This macro provides a cost-effective interface for PLCs that vary the speed of the drive using only digital signals.

A negative minimum frequency value defines one speed range. Example Example The drive runs a conveyor line. To enable the macro, set the value of parameter to 2 3-WIRE.

The drive will be fully operational as long as the motor rotates and generates energy to the drive. In the following examples the reference is in rpm. Connections The diagram gives an overview of connections.

Control panel Cleaning Use a soft damp cloth to clean the control panel.

ABB ACS350 User Manual

FlashDrop is an optional device for fast copying of parameters to unpowered drives. Available for two seconds at start, otherwise as long mankal 2max allowed by the drive temperature.

Speed values are used with vector control and frequency values are used with scalar control. Fieldbus adapter is connected to drive terminal X3.


Table Of Contents AC power line connection Brake resistor selection 1. Selecting The Power Cables Selecting the power cables General rules Dimension the input power and motor cables according to local regulations. Timed functions A variety of acs35 functions can be time controlled, e. If sequence programming is deactivated by falling edge of digital input DI1, state machine is reset to state 1. Covers on R0 and R1. Page Program features Short-circuit capacity Maximum allowed prospective short-circuit current at the input power connection as defined in IEC is kA.


Determine the required maximum braking power P for the application.

How to select a parameter and change its value Step Accs350 Display Page 24 Hardware description Page 57 About control panels Use a control panel to control the ACS, read status data, and adjust parameters. It provides three constant speeds. Read only copy of the Fieldbus Control Word.

For embedded fieldbus control, see chapter Fieldbus control with embedded fieldbus. Timed Functions Timed functions Kanual variety of drive functions can be time controlled, e.

Applicable standards The drive complies with the following standards: PID Control macro This macro provides parameter settings for closed-loop control systems such as pressure control, flow control, etc. Sequence programming can be applied in simple mixer applications as well as in more complicated traverse applications. Page ST8 error state: Terms and abbreviations Term Definition Actual signal Signal measured or calculated by the drive.

If delay time is set to zero, the drive resets immediately. Brake resistors ACS drives have an internal brake chopper as standard equipment.

Drive is programmed for traverse control with 30 sequences. Set the motor data to exactly the same value as on the motor nameplate.

Thermal overload protection of the motor According to regulations, the motor must be protected against thermal overload and the current must be switched off when overload is detected.