Buecher Wuermer

ASTM International ASTM D Tearing Strength of Fabric by . ASTM International. D Breaking Strength/Elongation Grab Method. ASTM D is a testing standard for determining the breaking strength and elongation of woven, non-woven, and felted fabrics and textiles. ASTM D is a popular testing standard for those needing to determine the breaking strength and elongation of fabrics and textiles.

Author: Nenos Dinos
Country: Romania
Language: English (Spanish)
Genre: History
Published (Last): 24 June 2004
Pages: 247
PDF File Size: 15.72 Mb
ePub File Size: 7.26 Mb
ISBN: 818-9-76113-599-7
Downloads: 40111
Price: Free* [*Free Regsitration Required]
Uploader: Kajishakar

Next Checking to see if you are a returning visitor…. Inch-pound units is the technically correct name for the customary units used in the United States.

ASTM D Breaking Strength and Elongation of Textile Fabrics Grab Test – Instron

Email addresses must contain the symbol. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more!

Link to Active This link will always route to the current Active version of the standard. Email addresses can only contain letters, numbers and the following special characters: Historical Version s – view previous versions of standard.

Subscribe to Instron News! Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. For this test, it is important to have an increased test data rate to ensure the capture a high number of data points. The method specifies a procedure to determine the maximum force and the elongation at maximum force of textile fabrics using a grab method. WaveMatrix 2 for Dynamic Testing.

A grab test is a tensile test in which only the center part of the specimen not the full width is gripped in the jaw faces.

There is no simple relationship between grab tests and strip tests since the amount of fabric assistance depends on the type of fabric and construction variables. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in light of the known bias. SI units is the technically correct name for the system of metric units known as the International System of Units.

  BEHRINGER PX3000 MANUAL PDF

The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining in any way. The values stated in either acceptable metric units or in other units shall be regarded separately as standard. Rapid data capture rate with Instron’s controller allows data peaks and valleys to be captured accurately at up to 2, points per second Instron pneumatic side action grips with rubber faces are well-suited to gripping nearly all types of fabric specimens for this test while maintaining high throughput It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements.

SI units is the technically correct name for the system of metric units known as the International System of Units.

The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining in any way. It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements.

Active view current version of standard. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question.

Onsite Training At Your Facility. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  CACOPHONY SONGBOOK PDF

ASTM D5034 Textile Strength and Elongation Grab Test

This test method is particularly applicable to high-strength fabrics. Rapid data capture rate Specimen gripping Instron’s Solution: Link to Active This link will always route to the current Active version of the standard. Contact Us View Accessories Catalog. Grab test specimens require much less time to prepare although they require more fabric per specimen. This standard mainly applies to most woven textile fabrics, but can be applicable to fabrics produced by other techniques. Special precautionary measures are provided for use when necessary for strong fabrics.

Inch-pound units is the technically correct name for the customary units used in the United States. Please confirm that you agree with our privacy and cookies policy to submit this form. The average results from the two laboratories should be compared using Student’s t -test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun.

Note 1—For the determination of the breaking force and elongation of textile fabrics using the raveled strip test procedure and the cut strip test procedure, refer to Test Method D For the determination of the breaking force and elongation of textile fabrics using the raveled strip test procedure and the cut strip test procedure, refer to Test Method D The breaking force determined by the grab procedure is not a reflection of the strength of the yarns actually gripped between clamps and cannot be used for direct comparison with yarn strength determinations.

Two sets of specimens are prepared, one in the warp machine direction and one in the filling cross direction.