Buecher Wuermer

The current test method is ASTM F dye penetration. . ASTM F – 98 ( Reapproved ) Standard Test Method for Detecting Seal. Leaks in Porous. 1 This test method is under the jurisdiction of ASTM Committee F02 on Flexible Last previous edition approved in as F – ASTM F testing defines materials and a procedure that will detect and locate a leak equal or greater than a channel formed by a 50 μm ( in.) wire in.

Author: Zurr Tojind
Country: Canada
Language: English (Spanish)
Genre: Medical
Published (Last): 21 March 2007
Pages: 39
PDF File Size: 15.28 Mb
ePub File Size: 15.37 Mb
ISBN: 683-4-36988-587-6
Downloads: 36925
Price: Free* [*Free Regsitration Required]
Uploader: Vuk

In the Burst Testair is introduced into the package at a predetermined pressure and flow rate.

There is no general consensus regarding the level of leakage that is likely to be detrimental to a particular package. The dye solution used in penetration testing will wick through any porous material over time, but normally not within the suggested maximum time. As a guide, each Test Method above recommends observing each seal for a maximum of 5 asym on a 4-sided package 20 seconds total. These leaks are frequently discovered at seals between package components of the same or dissimilar materials.

Water already in the seal defects may render them undetectable with a dye penetrant. The dye will have discolored the surface of the material. This pressure creates the force needed to rupture the seal.

Overview of ASTM F Dye Penetration Integrity Test

The porosity or lack thereof of the package material determines the inflation rate for the burst test. For more information visit www. Observe each seal for a recommended duration of 5 to 20 seconds. ASTM F procedure requires that the dye penetrant have good contrast to the opaque packaging material. Please contact us with any questions you may have about ASTM F, or if we can help you with any other testing questions or projects.

  GERHANA DI GAJAHMUNGKUR PDF

Leaks may also result from a microscopic pinhole in the packaging material that is invisible to d1929-98 human eye. Most commonly, an eyedropper or pipette is used to apply the dye penetration solution between the transparent f192-998 porous materials of the unsealed area.

Along the extended f11929-98 area beyond outer seal edgethe transparent material is separated from the porous material with use of a finger, paperclip, etc. Harmful biological or particulate contaminants may enter the device through leaks.

ASTM-F1929

If wicking does transpire, it may be verified by observing the porous side of the subject seal area. Packaging must be free of condensation or any other source of liquid water. If ASTM F testing is used as the quality control method, the test specimen must consist of a complete packaged device. F1929-998 keep this in mind when developing your studies and validations.

Overview of ASTM F1929 Dye Penetration Integrity Test

Place a bead of solution between the two materials along the outer edge of the package seal, ensuring the entire outer edge of the seal is wetted with the dye solution. Requirements ASTM F testing is limited to porous materials which can retain the dye penetrant solution and prevent it from discoloring the entire seal for a minimum of 20 seconds. A dye penetrant solution is applied locally to the seal edge to be tested for leaks.

  JEAN LUC NANCY THE INOPERATIVE COMMUNITY PDF

Because air escapes through the walls of a porous package during inflation, the flow rate must be increased to compensate for the lost air through the walls and create the back pressure in the porous package. The Creep Test provides a test for slow shear of the adhesive bond similar to a dead weight hanging on the seal.

The package will be visually inspected for dye penetration after contact with the dye penetrant for a specified time. Learn more about the different testing services provided at each location.

However, since G1929-98 F testing is designed solely to detect leakage, components that illustrate any indication of leakage are usually rejected. The Eyedropper method requires the packages to have an unsealed area that extends beyond the outer edge of the seal.

Observe the package for any leaks originating from the inside edge of the package seal towards the outside edge of the package seal. Here is a quick overview of the changes: