Buecher Wuermer

table in the DSx 1-Wire network cables data sheet. Both adapters are based on the DS USB-to-. 1-Wire bridge chip. Free software drivers for. Both adapters are based on the DS USB-to-. 1-Wire bridge chip. See the DS data sheet for the conditions where SUSO is active. Revision C of the. DS Usb to 1-Wire Bridge Chip. FEATURES. Communicates at regular and overdrive 1Wire® speeds Supports 12V EPROM programming and stiff 5V.

Author: Shaktijora Grogar
Country: Montenegro
Language: English (Spanish)
Genre: Video
Published (Last): 12 April 2008
Pages: 485
PDF File Size: 8.49 Mb
ePub File Size: 10.21 Mb
ISBN: 484-8-18282-687-8
Downloads: 36165
Price: Free* [*Free Regsitration Required]
Uploader: Akirisar

It happens obviously while accessing the one-wire bus: But i think the usb power supply isn’t switched on or off. Hm, at the weekend i will have access to some testing dz2490 and then i will check this. The irc server is down? Through control registers, the 1-Wire timing can be fine-tuned. The single-channel versionDSthe duration of the active pullup is fixed on the DS USB disconnect, address 5 usb Thought you are dataxheet about somebody else: Since you have that, the HV pin on the level shifter isn’t strictly necessary.

In case a device has a failure, the usb driver can turn off the power for the specific port. In addition, a correct programming pulse can only be generated.

A 6 Ohms resistor will limit datashee current at 5V short circuit to about mA. Again, I have no idea what the standard says about that. But in the meantime i’ve testet the two built ds interfaces on several other machines and they worked flawlessly there. If you do use local power, the onboard 3. Revision C ofproduction tested.


This sounds first more like a hardware problem to me.

Usb problem with DS2490

The DS surrounding hardware? However, the host may cut the power to a USB port. In both chips theis completed. Indeed I am totally new to electronics so I’m just trying to make sense of this as I go along: The DS iscontrol output for an additional strong pullup Q1. Wouldn’t this be a chicken and egg problem?

Any review, datasheeh, dissemination or other use of or taking of any action in reliance upon this information by persons or entities other than the intended recipient is prohibited. But now I’m not longer sure when this happens besides from overcurrent.

Best wishes, Klaus This SF. The 8-channel version of the DS makes it easy to split a larger application into smaller networks with fewer 1-Wire devices on each line.

DS 데이터시트(PDF) – Maxim Integrated Products

It may do so if the device is to be powered off due to power saving issues. Thanks for the clarification. Hm, as written even this passive hub hub without own power supply helps. Return to Other Products from Adafruit. Please be positive and constructive with your questions and comments.

ds datasheet & applicatoin notes – Datasheet Archive

The shape of the uncontrolleddamage the device as well as the DS You could use an Kind regards Klaus PS: Of course the peripheral device may be in some sort oft sleep mode until it’s initialized by a driver. See the DS data sheet for the conditions whereadapter. Thanks for posting it. The reason may be that absurd USB “devices” like this http: You have to limit the current flowing into empty capacitors by applying a resistor or better a choke coil to the supply lines.


USB disconnect, address 4 usb DS 0x 0x 0x04FA. But the power supply on the usb-bus is on all the time. That may be low enough not to trigger any overcurrent circuit in the host adapter.

(PDF) DS2490 Datasheet download

Free forum by Nabble. The shape of the uncontrolled falling edge is determined by the capacitance of the. The slope is determined by the load on the bus and theDSinitiated falling edges. Empty capacitors are like short circuits. In reply to this post by Sven Geggus. Spikes and something like that on the power lines should be sufficiently blocked by Capacitors and RF-Chokes which i already placed there.