Reference number. ISO (E). This is a preview of “ISO “. Click here to purchase the full version from the ANSI store. BS EN ISO Safety of machinery – Permanent means of access to . Unlike Parts 3 and 4 of the standard, BS EN ISO has no clause. Safety of machinery – Permanent means of access to machinery –. Part 2: Working platforms and walkways (ISO ).
|Published (Last):||10 April 2012|
|PDF File Size:||20.84 Mb|
|ePub File Size:||13.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
Nevertheless, it would be prudent to verify the safety requirements 1412-2 by calculation or testing. In other words, when designing and specifying means of access, consideration should be given to preventing unauthorised access. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. As well as applying to rigidly attached means of access, the standard also applies to non-powered adjustable or movable parts such as sliding or folding ladders.
For example, rather than require an access point so that lubrication points can be reached, lubrication points should ios made accessible from ground level or a lubrication circuit isp pump could be installed.
Earlier this White Paper mentioned the need to prevent 141222- access. This part of BS EN ISO gives requirements for non-powered working platforms and walkways which are a part of a stationary machine, and to the non-powered adjustable parts e.
Clause 5Specific requirements of ladder systemsprovides extensive information relating to ladder design, including the profiles and dimensions of rungs round rungs are not permitted.
BS EN ISO 14122-2:2016
ENOso Gaps to Avoid Crushing Explaining the requirements of the standard for minimum gaps to prevent crushing. Search all products by. Free Ergonomics Guidance European Commission publication Guidance on the application of the essential health and safety requirements on ergonomics. This is Part 2 in a series of four international standards which define general requirements for safe access to machinery.
Another point to note from the definitions is that handrails must be rigid, which excludes the use of ropes, chains or cables. However, it is almost inevitable that Part 3 will also be required, because this covers the guard-rails that are usually necessary with platforms and walkways.
The previous editions cease to provide a presumption of conformity to the Machinery Directive on 31 December Means of access, as with guarding, help to control access to machine-related 11422-2 under different circumstances — such as operation, cleaning and maintenance — and should not themselves introduce significant new risks.
A permanent means of access is fixed to the machine or an adjacent structure in such a way that it cannot be removed without the use of tools. References are made to other subclauses that help in determining which type of access should be selected, but the point to note is that there must be good reasons for using any means of access other than those listed higher up the hierarchy.
It specifies minimum requirements that also apply when the same means of access is required as the part of the building lso civil construction e.
Furthermore, three-point contact needs to be maintained except for very brief periods eg starting a screwheavy objects should not be carried, leaning ladders should be secured and, if stepladders are used and side loads are imposed, then the stepladder should be secured.
As part of the free survey, the safety engineers provide a short written report that identifies areas of non-compliance and actions that can be taken to reduce risk, improve safety and comply with PUWER.
If an anti-climb device is fitted to a ladder, a written warning or audible signal is not adequate for access control. Annex A gives examples of changes that can be made to the machine or system to make better access possible.
Io faster, easier way to work with standards. General requirements for the design and construction of fixed and movable guards. However, great care should be taken with ribbed ramps, bearing in mind that subclause 4.
Note that subclause 6. If guard-rails are being installed alongside platforms or walkways, Part 3 will have to be used in conjunction with Part 2 as well. Conveyor Guarding Explaining the hazards associated with conveyors, regulations and standards, and how to safeguard conveyors 1122-2 adversely affecting productivity. Click to learn more. You may find similar items within these categories by selecting from the choices below:.
White Paper 7 – BS EN ISO | Free Downloads | Procter Machine Safety
Find Similar Items This product falls into the following categories. Clause 7Specific requirements applicable to guard-railsstates that guard-rails shall be installed when the height of the possible fall exceeds mm, if the gap between the platform and machine structure exceeds mm or if the protection provided by the structure is not equivalent to a guard-rail.
Machine manufacturers small, medium and large enterprises Health and safety bodies regulators, accident prevention organizations, market surveillance, etc. Some leeway is provided for designers, as shown by this example from subclause 5.
Your basket is empty. The four parts are, in full:. For testing stepladders, the reader is referred to ENLadders. Plates-formes de travail et passerelles. However, the same subclause states that the minimum height of the guard-rail shall be mm, so it appears that the former may be a typographical error and the height of the handrail should be greater than or equal to mm.
Remember that compliance with standards is not mandatory but is strongly recommended.
Furthermore, a permanent means 141122-2 access can prove to be very cost-effective compared with the cost of erecting scaffolding on multiple occasions. Permanent means of access to machinery. Overview Product Details What is this standard about?